Description:
Ah, the age-old dilemma: you want to soar through the skies with a drone you've pieced together with your own two hands, yet the mere thought of wading through the quagmire of compatibility checks and part-picking sends you into a tailspin. Fear not, aspiring aviator! We've concocted the perfect antidote to your drone-building woes with our DIY Kits. Say goodbye to the endless research spiral and hello to more sky time.
Let's unwrap the treasure chest that is our 7-inch, DJI HD FPV + ELRS kit. It's like the Swiss Army knife of drone kits, only cooler and with fewer tiny scissors.
Frame : Source One (7 Inch) - Because flying a flimsy drone is like bringing a knife to a gunfight.
Flight Stack :GEPRC Taker F405 BLS 60A Stack V2 - It's the brain and brawn of your drone, minus the existential crisis.
Motors : Emax Eco 2807 1300kV - These are what will give your drone the lift of an eagle and the grace of a ballet dancer (on a good day).
Propellers : HQ Prop 7x4.5x2 - Without these, your drone is basically a very expensive paperweight.
Receiver : Happymodel EP1 Dual TCXO RX - Because losing signal is only cool if you're a mysterious radio broadcaster from the 1940s.
Digital FPV Air Unit : DJI O4 (lite) - So you can see what your drone sees, minus the existential angst.
And because we're not the type to leave you hanging, here's what else you might need to get your drone off the ground and not just staring at you judgmentally from your workbench:
Batteries : Choose between TheFPV 2000mAh 6S or CNHL 6S 2000mAh. Because the only thing worse than a dead drone is a dead... well, anything, really.
Chargers : SkyRC e680 1-6S Charger for the lone wolf or SkyRC D100 Neo 2-6S Charger if you prefer a bit of company.
Radios : Go for Radiomaster Pocket (ELRS, not the one that sounds like a salad dressing) or Radiomaster Zorro (also ELRS, because consistency is key). And if you're feeling extra fancy, the DJI Remote Controller 2 is your friend (just don't mix it up with the ELRS receiver, or you'll have a very sophisticated paperweight).
Goggles : Choose between DJI Goggles 2 or DJI Goggles Integra, because flying blind is only cool in metaphorical inspirational quotes.
So there you have it. A drone kit that's so ready to fly, it's practically begging you to take it to the skies. Just add a dash of assembly and a sprinkle of pilot flair, and you're all set to crash... I mean, soar!
What you get
This is our 7-inch, DJI HD FPV + ELRS kit. The parts list is as follows:
-
- Frame : Source One (7 Inch)
- Flight Stack (Flight Controller + ESC) : GEPRC Taker F405 BLS 60A Stack V2
- Motors : Emax Eco 2807 1300kV
- Propellers : HQ Prop 7x4.5x2
- Receiver : Happymodel EP1 Dual TCXO RX
- Digital FPV Air Unit: DJI O4 (lite)
- Included in you kit are the necessary VTx and camera adapter 3D prints to fit your new DJI O4 (lite)
Extra Parts
If you don't already have the rest, we recommend the following to get started:
- Battery : TheFPV 2000mAh 6S OR CNHL 6S 2000mAh
- Charger : SkyRC e680 1-6S Charger (Single Channel) OR SkyRC D100 Neo 2-6S Charger (Dual Channel)
- Radio : Radiomaster Pocket (ELRS, NOT CC2500) OR Radiomaster Zorro (ELRS, NOT 4-in-1)
- Radio Alternative: DJI Remote Controller 2 ( NOTE : If using this radio, do not install the ELRS receiver, and ensure that all O3 signal wires are connected to the flight controller)
- Goggles : DJI Goggles 3 , DJI Goggles 2 OR DJI Goggles Integra
Suggested Tools
If you don't have any tools, this is what we suggest:
- UMT FPV Drone Tool Kit with Case (10pc) OR TheFPV 18pc Drone Tool Kit
- Sequre SQ-001 65W Portable Soldering Iron Kit OR UMT 80W Soldering Iron Kit with M900 Compatible Tips
- DroneBuildr Zip Tie / Cable Tie (Pack Of 20)
- DroneBuildr Wire Mesh Paracord Cable Sleeve (for your motor wires)
- Vifly ShortSaver 2 Smart Smoke Stopper
- DroneBuildr 100pcs 10cm Heat Shrink Tube Kit
Note: Accessory pack contents may vary based on supply availability.
(0 ) Reviews:
No reviews yet. Be the first to review!