DarwinFPV 3-4S F411 FC 4 IN 1 30A ESC Flight Stack

Description:

DarwinFPV F411 3-4S 30A Stack: The Low-cost Pathway to Soaring Heights!

Don't let your wallet pull you down when your dreams are soaring high in the skies. Join hands with the most budget-friendly co-pilot you could ask for, the DarwinFPV F411 3-4S 30A Stack. Lovingly engineered for entry-level FPV drone enthusiasts, it's the Robin to your Batman, the Chewbacca to your Han Solo - an essential ally in your high-flying endeavours. And oh boy, do we have it armored!

This stack doesn't just stand by your side; it valiantly takes a hit for you! We've smothered the flight control and ESC with a robust glue coat, creating a superhero shield against frequent novices' blow-ups. It's like an FPV pilot's suit of armor, on a budget!

Key Product Highlights:

• Glue-treated Goodness : With an exclusive glue coat, we've taken the defense to the next level. It's like a forcefield against metal particles, sand, gravel, weeds, or even pesky dewdrops. The DarwinFPV Stack is more protected than a baby kangaroo in its mother's pouch!
• Feature-Rich and Feather-Light : This stack sports a built-in barometer, SD card slot, and a bunch of rich interface resources. It's the Swiss Army Knife of FPV stacks!
• Image Stability : This stack's FC integrates an LC filter, reducing VTX interference from system voltage changes during drone acceleration and deceleration. It's like a stabilizing rod for your image quality, so you can enjoy smooth and clear flight footage.
• Firmware Compatibility : Note to the tech aficionados out there! Currently, the black box function of the firmware "DARWINF411" may not be compatible with Betaflight 4.3.0 and 4.3.1, but we're expecting it to be included in the official 4.3.2 version. If you need to use the black box urgently, please upgrade to the 4.4.0 development version or downgrade to 4.3.0_RC3 and below firmware version.
• Receiver Support : This stack can work with receivers of most protocols out there. From Frsky XM/XM+/R-XSR, Futaba Receiver, DSM/DSMX, FlySky Receiver, TBS Crossfire Receiver, AC900 to PPM, PWM, IBUS, SBUS, SPEKTRUM, and CRSF of ELRS. It's like the United Nations of receiver support!

Specification

FC

MCUSTM32F411

GyroMPU6500

OSDAT7456E

Black boxbuilt-in SD Card slot

FirmwareDARWINF411

BEC output5V

Input Voltage3-6S LIPO

Reserved Connector: 1x SBUS(RX1 inverter)2x Uarts(1,22x Softserial1x I 2 C1x RGB1x Buzzer1x USER(A15)1x USB

Pcb Size37mm x 37mm

Mounting Holes20mm x 20mm30.5mm x 30.5mm

Attention!!! Because the black box function of the target firmware "DARWINF411" is currently not compatible with Betalight 4.3.0 and 4.3.1 (the black box function is expected to be added to the official version 4.3.2) If you need to use the black box urgently, please upgrade to the 4.4.0 development version or downgrade to 4.3.0_RC3 and below firmware version.

ESC

MCUEFM8BB21

Continuous Current30A

Peak Current35A 10S

BEC outputNon

Input voltage3-4S LIPO

Throttle SignalDshot600Oneshot125

Current Sensor Non

MOS3 x3

TargetG_H_30

PCB Size29mm x 31mm

Fixed Hole20mm x 20mm

Weight4.9g

Receiver Support

Frsky XM/XM+/R-XSR

Futaba Receiver

DSM/DSMX

FlySky Receiver

TBS Crossfire Receiver

AC900

It supports receivers of most protocols on the market, such as PPM, PWM, IBUS, SBUS, SPEKTRUM and CRSF of ELRS.

In the Box:

Every DarwinFPV 3-4S F411 FC 4 IN 1 30A ESC STACK comes with a 20AW power cable, XT30, cable pack, 1.8cm 6Pin single SH1.0 wire, and a sticker for a complete, out-of-the-box solution.

In short, if you're on the hunt for the most cost-effective FPV stack to assemble yourself, look no further! The DarwinFPV F411 3-4S 30A Stack is the Holy Grail you've been seeking!

So why wait? Jump onboard, fasten your seatbelt, and let's conquer the skies together. After all, the sky's not the limit when there are footprints on the moon!