Description:
The Crux3 is a great flying and affordable "toothpick" style quadcopter, maybe not strictly a toothpick but close enough. You also have the option to mount an insta360 go for some cool stabilised footage.
Key Features
- 41gram 1-2s brushless Toothpick drone
- New AIO 4in1 CrazybeeX flight controller
- CADDX ANT 1200tvl Camera
- New 1202.5 brushless motor
- XT30 connector
- Compatible with Insta360 Go Camera ( this camera is NOT Included, you can add it by yourself.)
Specification
- Brand Name: Happymodel
- Model: Crux3
- Item Name: 115mm F4 OSD 1-2S 3 Inch Toothpick FPV Racing Drone
- Wheelbase: 115mm
- Size: 97x97x35mm (without propellers)
- Optional Receiver Version:
- Internal SPI Frsky version (Compatible with ACCST D8/D16, Recommend D8 mode)
- Internal SPI Flysky version(Compatible with AFHDS and AFHDS-2A Flysky transmitter)
- Internal SPI DSM2/DSMX version(Compatible with Spektrum or Multiprotocol DSM2/X radio)
- External Frsky RXSR receiver version(ACCST D16 sbus output)
- External TBS Crossfire Nano receiver version
- Weight: 41g (without battery)
- Recommend Lipo Battery: 2s 350mah/400mah/450mah/520mah Battery ( NOT Included)
Detailed Component Specifications
| EX1202.5 6400KV Motor |
Configu-ration:9N12P
Stator Diamter:12mm
Stator Length:2.5mm
Shaft Diameter:1.5mm
Motor Dimension(Dia.*Len):14*14.5mm
Weight: 4.4g
No.of Cells(Lipo):1-2S |
| Gemfan 3018 2-Blade Propeller |
Center Thickness:5.5mm
Prop Diameter:76.5mm
Center Hole diameter:1.5mm
|
| CrazybeeX FR V2.2 F4 Flight Controller |
MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU6000 (SPI connection)
Board Size: 28.5x28.5mm
Power Supply: 1-2S battery input (DC 2.9V-8.7V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G VTX
Built-in SPI Frsky/Flysky receiver or no receiver
Built-in 5V 1A BEC(Frsky SPI RX Version) CRAZYBEEX FR V2.2 FC Firmware target: CrazybeeF4FR(Flysky SPI RX Version) CRAZYBEEX FS V2.2 FC Firmware target: CrazybeeF4FS(DSM2/X SPI RX Version)CRAZYBEEX DXS V1.0 FC firmware target: CrazybeeF4DXS
(External Frsky RXSR Version) CRAZYBEEX PNP V2.2 Firmware target: CrazybeeF4DX
(External TBS CRSF NANO Version) CRAZYBEEX PNP V2.2 Firmware target: CrazybeeF4DX
|
| Onboard 5A BL_S 4in1 ESC |
MCU upgraded to EFM8BB21
Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: S_H_50_REV16_7.HEX
Default protocol: DSHOT600 |
| Onboard Frsky SPI D8 Receiver Version |
SPI BUS receiver Frsky D8 compatible
Compatible Non EU transmitter D8 modelChannels: 8ch
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m |
| Onboard Flysky SPI receiver Version |
Protocol: AFHDS and AFHDS-2A Switchable
Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
No ground interference ( Transmitter and receiver 1 m from the ground): 200~300mFailsafe support |
| Onboard DSM2/X SPI receiver Version |
SPI BUS receiver DSM2/DSMX compatible
Channels: Max 12ch
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m
RSSI enable (show on the goggles)
|
| External Frsky R-XSR receiver version |
Weight: 1.5g
Number of channels: 16CH (1-16CH from SBUS channel, 1~8CH from CPPM channel)
Operating Voltage Range: 3.5V~10V
Operating Current:70mA@5V
Firmware Upgradable
Compatibility: FrSky X Series modules and radios in D16 mode
Could support Frsky New ACCESS Protocol ( Upgrade firmware)
|
| External TBS CRSF Nano receiver version |
Original TBS CROSSFIRE Receiver ,CRSF Protocol , Official TBS transmitter compatible |
| Onboard 5.8G 40CH 25/200mW VTX |
Output power: 25mw~200mw switchable
Frequency: 40CH
Input voltage: 3.3V 5.5V
Current consumption: 300mA(type)
Frequency: 5.8GHz 5bands 40 channels
With Race bandSmartaudio ready |
| Caddx ANT 1200TVL Camera |
Image Sensor: 1/3" CMOS Sensor
Horizontal Resolution: 1200 TVL
TV System: NTSC or PAL Switchable
IMAGE: 4:3
Synchronization: Internal
Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000
S/N Ratio : >52dB (AGC OFF)
Video Output: CVBS
Lens: 1.8mm
Min. Illumination: [email protected]
Auto Gain Control: YES
BLC: YES
WDR: Global WDR
DNR: 3D DNR
Dimensions: 14*14mm(with bracket to 19*19mm)
Wide Power Input: DC 3.7-18V
Work Temperature: -20~+60
Weight: 2g (N.W.)
|
Included
- 1x Crux3 Frame and Canopy
- 1x F4 Flight Controller AIO 5A ESC Board
- 1x 5.8G 25-200mW VTX ( built-in Flight controller)
- 4x Happymodel EX1202.5 6400 KV Motor
- 4x Gemfan 3018 Propeller CW
- 4x Gemfan 3018 Propeller CCW
- 1x Caddx Ant 1200TVL Global WDR with OSD 2g Ultra Light Nano FPV Camera
- 1x Screw Driver
- 1x Propeller Disassemble Tool
(0 ) Reviews:
No reviews yet. Be the first to review!