Description:
Features
- Battery voltage LED status light (illuminated IF logo on the bottom)
- GoPro TPU bottom stand (GoPro protector not included)
- Lightweight Side Panels Design - Keep Your Rig Clean
- XING2 2809 1250KV efficient wide stator motors
- GPS pre-installed for more safety at a distance
- 360 TPU protection, FPV cam protection
- 6mm rigid arm design for more stiffness
- Top- and bottom battery mount option
Li-Ion battery use : Be aware that Li-Ion battery packs do not have the same power output than Li-Po batteries. Please consider installing 2x 4000mAh batteries in parallel if you want to fly far, fast and safe. This can greatly reduce the stress per cell and hold a safe Voltage until the end of the flight. The 1x 21700 4000mh battery configuration is meant for more confined and less windy conditions!
Li-Po battery use: Li-Po batteries have a higher C-rating, more output power (amperage) and hold a more stable cell voltage throughout the flight. If you're beginner or don't want to mess around with Li-Ion batteries and their Pros and Cons, please consider flying Li-Po batteries first. Big batteries can be top mounted, even bigger or longer batteries can be strapped to the bottom of the frame.
GPS functionality to find your way back and Betaflight GPS Rescue mode ready to setup (default OFF to prevent unexpected behavior; Setup instructions included). Vertical and horizontal TBS Crossfire antenna mounts are included to cover you and your antenna dead-ends just in case. GoPro universal TPU bottom stand included; fits your original GoPro bracket and our TPU GoPro protectors (sold separately).
Changes between Chimera7 and Chimera7 Pro
- SucceX-D F7 V2.2 Stack (F7+50A ESC) upgraded to BLITZ F722 Stack (F7 V1.1 + 55A 4in1 ESC)
- New Lightweight Side Panels Design - Keep Your Rig Clean
- XING 2806.5 upgraded to XING2 2809 1250KV
- 7-inch frame upgraded to 7.5inch
PRE-TUNED & PRE-SETUP:
- Is this your first BNF or are you just starting through with FPV? This article might probably help: General Guide // iFlight BNF
- Don't worry about tuning, we did that for you already! A basic PID- and Filter tuning was applied for a great flight experience!
- To restore lost tunes or updates, please check our linked article on "Firmware/Factory Dumps"
- Angle-Mode (self-balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess!
- Please check our linked article on "How to disable Angle-Mode, activate Acro-Mode"
- GPS Rescue is OFF by default to prevent unwanted or unexpected drone behavior.
- Please check our linked article on "GPS Rescue Mode // Setup"
Specifications
- Weight: 695g (without battery and GoPro mount)
- Total Dimensions: 258*200mm (body dimension)
- Upper(middle) Plate Thickness: 3mm
- Bottom to Top Distance: 20-29mm
- ESC: BLITZ E55 4-IN-1 2-6S ESC
- Bottom Plate Thickness: 3mm
- Camera Plate Thickness: 3mm
- Top Plate Thickness: 3mm
- Geometry: DC (DeadCat)
- HQ 7.5X3.7X3 Propellers
- Arm Thickness: 6mm
- XING2 2809 1250KV
- FC: BLITZ F722
ELECTRONICS // BLITZ F7 Stack (F7 V1.1 + 55A 4in1 ESC)
FC // BLITZ F722 Flight Controller
- Mount pattern: 30.5*30.5mm / 4mm PCB hole diameter
- Smartaudio / IRC Tramp VTX protocol supported
- Firmware target: IFLIGHT_BLITZ_F722
- Motor outputs: 4x (SH1.0 connector)
- Flash: 32MB (Blackbox flash)
- I2C serial: SDA / SLA pads
- Dimensions: 36.5*35 mm
- Barometer: DPS310
- OSD Chip: AT7456E
- LED controller: Yes
- MCU: STM32 F722
- Beeper pad: Yes
- Gyro: BMI270
- Weight: 7.8g
- UARTS: 6
ESC // BLITZ E55 4-IN-1 2-6S 55A ESC
- Supports: DShot DShot150/300/600/MultiShot/ OneShot etc.
- Mounting Holes: 30.5*30.5mm/4mm
- Target: IFLIGHT_BLITZ_G2
- Supports 2-6S Lipo input
- Current sensor: Yes
- Constant: 55 Amps
- Current rate: 200
- Burst: 65 Amps
- Weight: 15.3g
- MCU G071
- BEC: No
VTX// BLITZ 1.6W VTX Adjustable
- Betaflight IRC Tramp Configuration: Please download the attached VTX table for Betaflight!
- IRC Tramp VTX table values: 25mW/400mW/800mW/1600mW
- Power levels: PIT/25mW/400mW/800mW/1600mW
- All our VTX tables can also be found here: LINK
- Lightweight: 18.9g (excluding antenna)
- Mounting pattern: 30.5x30.5mm/3
- Channels: 40 (including Raceband)
- VTX telemetry: IRC Tramp
- Input voltage: 7V36V
- Interface: MMCX
Chimera7 Pro Analog BNF Included Components and Parts
- 4 x HQ 7.5X3.7X3 CW propeller + 4 x HQ 7.5X3.7X3 CCW (Color may vary)
- 1 x RaceCam R1 Mini 1200TVL 2.1mm 19*19 camera
- 1 x Albatross RHCP 5.8GHz SMA FPV Antenna
- 2 x iFlight Lipo Strap 20*250mm (Black)
- 1 x Pre-built and Tested Chimera7 Pro
Tips:
VTX is set to 25mW by default! Power levels above 25mW require a HAM license or have to be approved by local authorities! Please ensure you're flying legal frequencies and use our prepared Betaflight VTX tables according to your region.
(0 ) Reviews:
No reviews yet. Be the first to review!